Turkey did it some years ago (2005). Removed six zeroes and named it something like “new lira”. Then named it back to “lira” after most of the old money is out of circulation.
20 years later, I think some more zeroes are available to be removed :)
And if it’s the very first gen of the Leaf, then, as far as I know, they don’t have thermal management for the batteries. So it greatly stresses them both for discharge and charge and that manifests as reduced capacity.
Lithium cells are happy when they are around 20-25 degrees Celsius (about 75F?) but they don’t enjoy when it’s hot or cold. Likewise, they don’t enjoy full charges and discharges which I’d guess more probable in a smaller range car.
All in all, the first gen Leaf might not be a good benchmark for a more modern EV. Many things should be better now.
I think that applies to many other electronics they sell too. I find them pretty well engineered overall.
My guess is that it’s because they sell any particular piece of hardware in millions and it’s in their best interest to design it properly so they don’t have to deal with the returns.
Interesting approach. I have a feeling that this is intended for sparsely built houses (the typical american housing maybe?) since in a dense European city I’d imagine it would pick up tons of cell phone signals from other people in their own homes or, say, from people visiting the downstairs coffee shop terrace.
> Our service is ideal for detached homes, where our calibration (small, medium or large homes) lets the sensor distinguish between mobile phones on your property and those nearby. It is not suitable to homes (e.g. apartments) that share walls with other homes.
The 'fix' for that (applicable in some areas, not so much in others) would be to remember phone ID's and focus on numbers (and strength) of new ID's during the rental period.
A downstairs coffee shop would be a semi periodic flux of a particular size, a party would be a surge over and above that flux and persisting outside of coffee shop hours.
Again, pattern learning is only applicable in some scenarios .. but effective enough in those.
Phones randomize mac addresses so that probably wouldn't work. Presumably you can get a read on how many devices are scanning at once, but not track them long term.
One could safely assume that such a tool would likely be illegal in the EU, anyways, since that’s rather a lot of data collection activity to expose a homeowner to.
You can but it isn’t efficient. You lose (V_in - V_out)*I_led Watts to heat if you use a linear regulator.
You might ask why not connect them in series and get the voltage difference as small as possible. But the “forward voltages” of LEDs are highly temperature dependent and car battery voltage is (somewhat) engine rpm dependent (might swing between 12 and 13.8V between no rpm and some rpm. It’s kept flat at 13.8V)
They might turn off/block egr which reintroduces exhaust gasses to intake to reduce combustion temperature. The upside of this system is that it reduces NOx emissions, the downside is that you’re bringing a lot of soot inside the engine. They are abrasive.
Combine egr with pcv, which directs positive crankcase pressure into the intake, you get an oily sooty mixture caking inside the intake.
Combine this with swirl flaps, which create a small tornado at lower engine speeds for better combustion, you get caking on the flaps and your intake becomes halfway clogged.
These are my annoyances. But to be honest, it didn’t require cleaning even after 250.000 kilometers of driving. I saw the caking while doing some other work, but the engine was running fine
But there’s also the dpf, and the adblue stuff. Dpf is an issue only if you use wrong kind of oil and clog it. I’m assuming people remove the dpf to run coal, as it will get clogged extremely fast if you detune your engine. It might also be an annoyance if you want to mod the engine, but not sure on that front. And adblue is yet another thing to fill every now and then. No experience with that, but I assume it might annoy some.
When you start "rolling coal" all the "gains" by removing the EGR and PCV will be negated since you will be lining your valves with tar and ruining the oil.
Pretty benign until an idiot holds a small piece of sheet metal in one hand and drills it with the other. Guess how I know :)
To my defense, I put a bit of wood between the metal and my hand to prevent drilling my hand but little did I know how the drill catches the steel on the very last part of the cut.
I use both kinds very frequently so I can comment on this. The main difference is that SLA strength is more uniform and FDM strength is very directional.
And the strength of the output is highly dependent on the material for both printers. The typical resin is extremely brittle, but rather heat resistant. But you can get flexible or tough material which are both less brittle but also less rigid.
So to answer your question: not necessarily :) nylon-like SLA materials are pretty good for usable everyday items if you don't mind the slight fidelity losses (still better than FDM)
We have multiple form 3 printers at work too, and they are very slow! It takes an hour to automatically fill the resin tank (which I cheat by pouring myself) and supply costs are ridiculous. But I really like the rather consistent output quality and their software is awesome.
My comparisons are against my own printer, anycubic photon mono. I can get a new printer with the same price of a bottle of formlabs material :)
Yeah, you can't fill that guy without pouring it in. It just isn't happening with a new vat. The supply costs are indeed the worst part, too. However, we've had FAR from perfect, repeatable results with it. The Elegoo Saturn is DEFINITELY more consistent and repeatable. And yeah - lower end machines are kinda nuts. One moving part, etc. It's funny - they're a superior technology. How do we know? Form themselves went to mSLA on the 4 as compared to the SLA of the 3 with the complicated optical carriage.
Part of the reason is the compliance requirements. You need to pay quite a bit of money to USB-IF if you want to make anything USB and this is recurring as far as I know. There's also the other things like tests for EMC and ESD and whatnot. It either needs a big player to step up (you can use the same USB-IF membership for some tens of thousands of devices) or there should be a big enough market to support a smaller scale designer/manufacturer.
20 years later, I think some more zeroes are available to be removed :)